2-8-0 Consolidation - "connie"

Quick links to major topics on this page:

• Disassembly
• Fixing common problems
• DCC installation

Disassembly:

1) Roll engine over on fireman's side, locate forward end of reverse actuating rod under running board where it attaches to the valve gear.
Remove slot-head screw. NOT MAGNETIC! Don't lose it!
2) Roll engine onto its wheels. Remove all 4 screws and both smokebox supports (if you try to flex them out of the way, it will scratch the paint).
3) Roll engine over on it's back.
4) Remove ashpan (4 small screws).
5) Remove 4 screws about in the corners of inside of firebox under ashpan.
6) Remove one screw between cylinders under front truck.
7) Separate boiler from chassis. Pull motor wires down from boiler to reveal in-line plug. You may unplug for complete separation of boiler from chassis.

Fixing common problems:

There is a common problem that the motor/gearbox is loose on the mount arm.

Check motor for tightness to gearbox as outlined below:

Pull the lower gear cover, 4 screws, and front support bracket on top of frame to gearbox, 2 screws, lift the motor/gearbox off, removed 4 screws on one side and 2 on the other of the gearbox, separate the gearbox halves. The motor screws are located inside the gearbox. I removed the screws, locktited (222) and lubed before re-assembly.

Make sure you have the 2 brass collars that are on the drive axle INSIDE the gearbox before tightening the screws on the cover!

When re-assembling, make sure the sander pipes from the sandbox on top of boiler fit into holes provided in frame just forward of valve gear support bracket. They may spring backwards and rub on lead driver.

When reassembling the reach rod, drop screw into the hole, put the screwdriver into the screw to hold it in place, then use a pair of tweezers or a hemostat and lift the reach rod up. Start turning the screwdriver to find the hole while lifting the rod.

TOC

DCC decoder install:

Motor connections:

First, we will disconnect the motor from the original circuit. We will use the direction switch as the point of reference. There are 6 wires on the direction switch.

The first set of 2 wires go to the motor. They are black and red, and you can trace them from the motor.The wires from the motor are both black. They go to a small 2 pin socket. This connects to a 2 ping plug with red and black wires.

The second set of wires are orange and pink, and they solder to the main board near screw terminal 1.

The last set of wires go to the screw terminals, they are black going to 8, and red to 7.

(note there two other wires in 7 and 8, a black from the headlight on 8, and a yellow from the headlight in 7)

Leave the headlight wires in 7 & 8, and remove the motor wires only.

The decoder motor minus wire went to the red wire you removed from terminal 7. (NMRA decoder gray)
The decoder motor plus wire went to the black wire you removed from terminal 8. (NMRA decoder orange)

DON'T solder the wires yet, twist them together and put a bit of tape on it.

Track pickups:

The track pickups come from the "ashpan flicker board" and are black and red, at the very end of the main board, and are labeled "power". There are 2 empty solder holes "inboard" from the black and red, and then there are 2 wires in the "next" set of holes, and they are purple and white. The black goes to white, and the red goes to the purple.

The red wire connects to the fireman's or left side. The black wire connects to the engineers's or right side.

So now you can connect your decoder. Notice that the colors of the wires are "reversed" from the NMRA DCC standard.

Solder the right hand track pickup decoder wire to the hole nearest the black wire.
Solder the left hand track pickup decoder wire to the hole nearest the red wire.

Basic test:

Put the direction switch into the "large scale position".

Put the chassis on rollers, and call up loco 3 and check the direction of motion. If it is backwards swap the motor + and - wires, test again.

Solder the wires up.

Headlight:

The headlight wires are still connected to the screw terminals. We need to remove them from pins 7 (yellow) and pin 8 (black).

We used a NCE D408, so we connected the black wire to the decoder blue (common, which is is plus), and the yellow to the decoder white (output 1).

Test this before soldering. If the light does not light, reverse the connections.

Backup light:

The backup light wires are in the boiler too.T he backup light wires come from the pcb02 that is under the cab, which differs from how the published wiring diagram shows.

These 2 wires go up to the boiler, and one wire is gray and goes to screw terminal 2. In this loco, the black wire had been pulled out, but I suspect it was on screw terminal 8.

Connect the black wire to the decoder blue (common), and the gray wire to the decoder yellow (output 7)

Note on wiring: If you look at the 4 pin connector that goes to the tender, 2 of it's wires go to the CON08 pads on pcb02. These are the track pickups from the tender.The connector from the chassis goes to CON7. Then there are wires at CON06 which go up to the boiler.

The other 2 wires go to the CON2. You can see the traces for these 2 connections go "away" from the leds to 2 more pads labelled CON1.

(In the tender there are 4 binding posts. The track pickups use 2 of them and use black and brown wires to the connector, the led wires go to a second pair of binding posts with red and black wires.

Firebox flicker leds:

Unsolder these four wires from the end of the main board. Careful, there are 10 wires on the back end of the main board. Do not touch the 2 at the corner labelled "power".

So let's start with the yellow led, the red and white wires. On wire will have to go to the DCC decoder "common" and the other to a function output wire. We will use

From the picture above, the yellow led uses the red and white wires, and the red one uses the blue and brown.

We want to connect the red and yellow firebox leds on PCB02. This is wires red and white, white is positive and red is negative.

We will use the white and yellow wire from the D408, which is output 5. This is controlled by CV125. We will map it to function 6. This controlled by CV 40.

So set F4 to control output 6, so set CV40 to 4.

Now set output 6 to the lighting type required, so set CV125 to 135 (set for led, flicker effect, on in both directions)

red wire from led goes to decoder white and yellow

white wire from led goes to decoder blue wire

for the red led, the blue is negative and the brown is positive