Aristo RDC-1

This is a nice looking model, but many people have issues with them, so read the suggestions below. Many people complain about derailing.

This is a long model, and has a lot of overhang, so I also use this as a "clearance" test, both on the outside and inside of curves.

Notice that the prototype "A" end is the end the radiator nacelle is closer to.

Note: As of August, 2010, the longstanding RDC-1 was joined with a new RDC-3, which has completely different internal wiring, and an interior!

Notice that Ted has a vignette on the RDC-1, CLICK HERE.

Swapping out the traction tires: 

In general I don't like are the rubber traction tires. They rot, need replacement, and reduce power pickup. In the case of the RDC they cause operational problems.

What happens is the wheel with the traction tire pulls the loco more than the wheel without, and the wheels tend to actually climb off the rails in curves. Normally you don't see this in most locos, but the extra length, and sensitivity to cross level really shows up in the RDC. Also, since they normally run alone, there's really no need for a traction tire.

So my advice is swap them out for "solid" wheels.

Image 

They are easy to change out. You need 4 wheels, which will be two of Aristo part number29130 (package of 2 wheels).  These are labelled as "FA1 PLAIN WHEELS W/O GROOVE & TIRES WITH HEADER CARD".

To replace the wheels, you put the RDC on it's back, and remove a side frame. There are 2 small screws. They are in the 2 holes below the springs in this picture. It helps to use a magnetized screwdriver.



 Then remove the screw and star washer on one of the traction tire wheels. CAREFUL! The start washer WILL try to get away! If it drops under the truck and you do not see it, it may be sticking to the top of the truck, since the magnetism of the motor can trap it. Just be very careful not to let them get away.

I have a wheel puller that will just fit here. Turns out that the action of putting the puller under the wheel popped it off.  If you do not have a wheel puller, two large flat-bladed screw drivers on either side of the wheel will pop the old wheels off. This is a lot better way to do it as opposed to levering 2 screwdrivers between the motor block and the wheel.

I have my finger on the wheel, because, just the action of putting the puller in popped it off.


Image 

I spun the new wheels on the axle by hand a bit to feel confident they were matching the taper well, knocking off any high spots in the wheel casting. Replace the screw and star washer, and then the sideframe, being careful to try to find the "old" threads in the motor truck, since these are such small screws.


 Adding Kadee couplers:

According to the Kadee site, the 901, 907 and 789 are recommended. There is no further information or detailed installation information.

The 901 is a centerset coupler, and the 907 is that coupler in the 831 coupler box. These are the "new type" couplers. The 789 is a "original style" centerset coupler in the 831 coupler box.

Removing the stock couplers is easy, remove one screw for the long "centering spring", then remove the other screw that actually holds the coupler:

For the coupler, you need to drill a hole slightly offset in the Kadee,I "painted" the hole red to avoid confusion. Use a drill the diameter of the original screw, about 0.1"

The coupler height comes out perfect: (well maybe a touch low, maybe I'll go back in and trim a bit from the post)


 

Disassembly: (differences between RDC-1 and -3 noted)

Remove the car ends first, there are 2 screws on the bottom of each car end, and one very tiny silver screw in the roof. Try very hard to find drivers that fit these screws as closely as possible, the 2 screws underneath are under a lot of tension since they screw into the aluminum chassis. The small one on top can strip the head easily.

Herei's the two cap screws underneath, near the coupler:


Image

Here is the small screw on the roof, it's near the horn:


Image

Once you have the end caps off, let them dangle carefully, there is not much play in the wires. Here's what you see looking into the ends of an RDC-1. The cardboard aids the diffusion of the lighting. I decided not to try to reach through this, but to take it apart the rest of the way. The RDC-3 has an interior. This is the time to "untie" the knot of wires in an RDC-3.

 

 

Image 

Now there are 6 screws along the sides of the chassis, somewhat small. Again these are into metal, so get a good fitting driver. You can see two of them between the square battery boxes and the air tanks, right at the edges of the chassis: (again an RDC-1)Image

Support the whole thing carefully, since the end caps are loose, and can get scraped up by the chassis and shell. Pull the chassis out a bit and you can get inside.

Try not to whack the lights inside. When you put this back together, try feeding the speaker and smoke unit lights into the hole in the cardboard as you bring the chassis to the shell. This ensures the wires do not knock the lights around.


QSI DCC Install: (RDC-1)

To get to the Aristo socket, you remove the engine compartment box nearest the 3 slide switches. You don't need to remove the screws fully, the screws are in slots, not holes. The engine compartment boxes are the larger two underneath. There's nothing under the smaller 2 boxes, which look like battery boxes). Just loosen the screws, do not remove them.

When reinstalling the compartments, tighten the screws GENTLY, otherwise you will snap the slotted tabs off.  

If you need to access the speaker connector, it is under the other engine compartment box. you will see 2 connectors, the 3 pin one is the standard connector for the speaker used by Aristo on other locomotives, only the outside 2 pins are used. The 2 pin connector is paralleled with the motors.

So there are 2 ways to get the speaker wires down to the decoder.

  • One way is to make a jumper from the compartment that was intended to house the sound unit, over to the other compartment that has the socket for the decoder.
  • The other way is to unplug the speaker from the main board inside, and fish it down into the decoder area.

The easiest way to do this is open the car, and unplug the speaker plug from the circuit board. There are 2 sets of wires going from the chassis to the shelll. The red and black wires are the smoke unit, the two black wires are the speaker.

When you are inside you can remove the MU wires, in this (poor) picture, at the far back left, you see 2 solder pads and black wires, that's one mu cable.

On the right side at the back, behind the bulb, you see two more, that's the other mu cable. I remove them since I don't use them or want to look at them, or have them snag on a switch.

Again, the speaker wires come down from the top, and plug into the board, just to the extreme right in this picture, you can just barely make out the plug with the back wires. Pull this plug from the board.


Image


Now thread this wire and connector down to come out next to the Aristo socket. Button the chassis back together. You can see the wire and plug from the QSI and the speaker wire you threaded through in this picture:


Image

Now use 2 short pieces of wire, like 1/4 watt resistor leads to "jumper" the QSI speaker plug to the 3 pin Aristo speaker plug. 

 


QSI Sound file Tuning:

Notes on the prototype:

The RDC had 2 Detroit diesel motors, each powering only the outboard axle. The transmission was by Allision. There was a "TwinDisc" torque converter with lockup. Apparently the lockup was at about 55 mph. It's not clear yet, but it seems that by alternately pressurizing the 2 torque converters, this gave the equivalence of 2 gears, and the torque converters allowed the smooth transition in speed and obviated the need for a clutch. (The torque converters essentially were variable ratio transmissions like the old Buick "Dynaflow" transmission".

More as I research further.

Matching the sound file to the prototype:

I'm experimenting with a new sound file from QSI, that simulates the automatic transmission, the prototype had a torque converter.

First, the momentum and the notching CV's have no measurable effect on when it shifts gears.

As usual, I have the jerky/shaky startup and had to play with some parameters.

I followed the QSI tuning regimen by turning off BEMF (CV 56.4 = 0), then change start voltage (CV 2) so the loco starts moving at SS 8, and reduce it until it just stops. Then turn BRMF back on (CV 56.4 = 1)

My start speed came out at 8.

I set the pid's as on the QSI section, 10, 2, 5 for all 4 ranges, but this did not help much.

I raised the minimum BEMF (CV 56.5) to 20, although there was not much difference above 12.

The "upshifts" occurred at speed steps 11, 21, and 31

 The "downshifts" occurred at speed steps 30, 20, and 10

the horn and the bell sound nice

The prime mover volume is way too low, I raised the master volume to 127 and still too low, the air pumps and the fans can drown it out.


Visual improvements: 

Pete Eggink has done some neat stuff with his:

Basically he lowered the car, rotated the underbody detail 180 degrees to match the prototype, modified the air tanks.

I copied the below from the internet wayback machine. Pete, I'd like permission to post this, but we cannot find you!

  The first time I saw the Aristocraft RDC was at East Coast Large Scale Show in Somerset NJ a few years ago.  I liked its long, lean look and and accurately shaped ends and roof blister.  It took a couple years before it got to market, and I was waiting for the Reading paint scheme, but finally I gave up waiting and got a Long Island car as a Christmas present.  It didn't take too long before I took it apart to make a few modifications.

1.  First I disassembled the car and removed and discarded all interior lighting and cardboard baffles. Since it would be converted to battery power, I also removed the circuit board. I marked, removed, and cut the ends of the steel weight, so that the remaining piece was 16 3/4 inches long.
 
 
  
  The area where the truck swivels was cut out and moved up about 5 mm by adding styrene spacers and securing with nuts and bolts.  Also a new access hole was cut for the wires because the trucks were turned 180 degrees to shorten the car's rigid wheelbase from 26 down to 17 inches. 
  
 
 2.  I wanted to lower the body about 5 mm because the car seems to ride too high on the trucks.  I did this by raising the area where the trucks meet the body.  I cut 3 1/4 inch ovals in the aluminum frame around the truck mounts.  I made a spacer out of 2 pieces of .080 styrene, 3 5/8 by 5 inch, with a 3-inch-diameter round hole in the center. I sandwiched the spacers between the metal parts and bolted them all together with 8 bolts (I used the small nuts and bolts that come with Kadee 820 couplers).  I remounted the trucks but had to shave a little plastic here and there, on the trucks and the spacers, to enable them to swivel freely.

3.  To lengthen the run time on batteries, I de-motored one of the trucks.  To do this, I disassembled the power brick, removed the motor and the gear-axle side of the universal joint, and removed the gear inside the case on the swiveled axle.  Even with only one truck powered, this car can pull a decent size train!

4.  In order to improved the tracking with this long car, I reversed the orientation of the trucks, so that the swiveled axles would be toward the ends.  I also had to open a new access hole for the wiring. 

5.  Unfortunately, the underbody details on this model are a mirror image of the way they are on the prototype  (the motor housings should be on the right as you look at the car from the side).  Since I had already removed the circuit board, I didn't have to worry about the underbody switch panel.  I flipped over the steel weight, so its holes would line up with the mounting screws at the reversed locations.  Then I lined up the details, marked the holes, drilled, and reiinstalled in their corrected positions.

6.  The air tanks look far too low, so I shortened them by a half inch with wirecutters and a file and remounted them.  Because of the cuts, the original screw wouldn't work, so I improvised.
 
 
 
 
 7.  Next I rewired the unit for battery power.  I installed 18 volts' worth of 3-amp-hour NiMH batteries and a 75 mHz Onboard receiver.  I also installed a charging jack and on/off switch on one of the underbody motor assemblies.  See the battery power page for more details on circuitry.

8.  Next I linked the transmitter and receiver and got 'er running.  This was great fun!!
 
 
 9.  Next I made end walls, because the cardboard was removed in Step 1. I cut and fit .040 styrene walls between the cab and body at each end, and attached to the end pieces using pieces of styrene.  The color of the cab side of these end walls should be silver.

10.  I Installed a Kadee coupler on the front and shortened the Aristo coupler on the other end.

11.  This was a Long Island car I wanted to change to Reading.  I painted the orange end doors silver. Then I removed the paint on the aluminum sides with a single-edged razor blade.  For side-panel lettering I used 1/4 inch stick-on lettering and colored it with Polly-S black paint.  I made Reading Diamond Logos for the ends by shrinking an image on a copier using adhesive paper, and for the yellow I used a highlighter pen.

12. I masked the roof blister and painted the radiator screens flat black.

13. Then finally I reassembled the car; roof blister to body, body to frame, then ends to frame and body.

14.  After I ran this car for a while, I finally got around to installing LED headlights.  I removed the front cab and replaced the headlights with bright yellow LED's (All Electronics #LED-72).  I installed a 2-cell AA baterry holder to the back of the cab wall, wired a 2.5 ohm resistor in series, and installed a mini toggle switch under the motorman's door.  These lights are incredibly bright and they don't have that bluish hue that "white" LED's have.  For more details on this circuit, click
bright headlights.

15.  For the rear lights (red LED's), I found I could use the original Aristo LED's and wire it the same way I did the headlights.  With bright headlights in front and red taillights in back, it looks great.

 

Improving running:

Several people have reported that swapping the trucks such that the rigid axle is towards the center and the floating axle is towards the couplers helps. My opinion is that part of the trouble is the traction tires "grabbing", so I would try this AFTER you swap out the traction tires for regular wheels.

If you do this, you will basically have the car running opposite to the directional lighting, so you may have to reverse the motor leads inside. 

From Jeff Cairns: "I sort of went crazy with mine, and ended up making aluminum leaf springs to prevent derailments! The springs go between the chassis and the truck's A-frame, thus enabling the car to rock side-to-side. They can actually handle 4 foot diameter turnouts at full throttle now!"

Misc Data:

The motor in the RDC-1 is a Mabuchi 385 PH (same as dash 9)

 

the pic processor used for the voltage regulator is a PIC16C620A

Weather Underground PWS KCACARLS78