USA Trains Motive Power Main Page

(remember: links to sub-pages at the bottom of this page)

click to jump to the bottom

Quick links to major topics on this page:

 

Note: Click on the desired specific locomotive on the left. There are tips and techniques on each one in the menu.

Overview

USATrains is owned and operated by Charles Ro Sr. This will help explain when you see the Charles Ro advertisements. Their first loco was the NW-2 "cow" and "calf". They started making cars at a high level of detail, much sooner than Aristo. Their "Ultimate" line is highly detailed and well scaled. This is often the point of distinction between the "camps" of "who is the best".

I mostly will concern myself with their 1:29 line of products. They also have a line of 1:24 products that don't have the same level of detail, and I model 1:29.

They have a pretty extensive line of diesels, and while the drive mechanisms of their diesels do not have ball bearings, a much touted feature of Aristo, yet, overall reliability in the drive trains, i.e. motors and gears and bearings is about the same.

The diesels have a few, but consistent weaknesses:

  • loops that hold the coupler cut bars can be easily broken.
  • Cab doors have small springs and often something will break loose, either the spring or hinge if you play with them. Leave them alone!
  • "cracked" axles, where the metal half axles pressed into the plastic gear casting slip because the plastic casting has cracked. This happens

Smoke unit versions:

The newer products have fan-driven smoke units. You can see the fan motor in a cast zinc housing, and they have a little power board either nearby, or on the chassis. These units work well and rarely burn out.

The older smoke units are smaller, square, and flat and will definitely burn out if left on with no fluid. They do not have fans.They are not great smokers.

Interestingly, they both mount in the same "bracket", so you can swap the newer ones for old, for example in the F3s. The new units do need a small regulator board.

USAT Electrical variations:

The type and method of lighting varies from loco to loco, and also several locos have different versions. Many of the diesels have classification lights that change color from green to red according to direction.

  • Earlier locos tend to have low voltage lighting, 5 volts or so, and often a single set of 2 wires will power the number boards, the headlights and the classification lights. These usually use a large 2 pin connector.
  • Newer locos will use a smaller 3 pin connecter (but not always) and use track voltage to this connector, and 18v lamps for the headlights and number lights, or have the dropping resistors for LEDs.

The cab lights vary also. 

The bottom line when converting a USAT loco to DCC or something similar and you want to retain the original lights is to put the loco on rollers, power with DC, and then measure the voltage to the connectors and see if it is fixed or variable, reverses polarity or not, and what the max voltage is.

Don't follow this advice and I will guarantee you will burn out lights during an install.

Typical diesel drive mechanism:

The drive mechanism is basically a motor with worms on each end, driving an axle assembly which is a plastic gear casting, with 2 metal half axles (that have the wheels)  pressed into it. Some models have an extra reduction drive gear. The axles ride in brass bushings in the motor block which ride up and down in the motor block. On some blocks, there is a wire that presses down on the axles between the bushing and the gear to pick up power. The ends of the axles ride in bearings in the side frames, which also have power pickup wires.

Drive Problems:

All units have "splitting" of the gear where the metal half shaft enters it (on either side). The fix is a new gear, or better yet a new axle set. As far as I can tell, the way to tell is the old axles have "splines" along the length of the axle shaft. The newer axles have a helical knurling. The new ones still split the plastic housing, but not as often.

There are some ways to repair them, see the section on "Split Axles" on the left. Many people just buy new axles. 

Also, VERY IMPORTANT:  The assembly/alignment of the "brass" bushings on the axles is different between 2 axle trucks and 3 axle trucks. Failure to observe this and re-assemble properly leads to stripped gears. Many of the negative comments you may hear is from someone who actually screwed up their own locomotive, and then blame it on USAT. You are forewarned.

Details in each specific loco page, but the short answer is 2 axle locos have the flat side up, 3 axles have the point up (aligned like a diamond). The bushings on any "idler gear" shafts fit "flat".

Electrical system problems:

USAT locos have very few electrical problems. The electrical pickup is normally from metal bearings at the ends of each axle and LGB style "skates" or "sliders" that bear on the rails. On some locos there are additional wires "whiskers" that bear against the axles for even more pickup (inside the motor block). The only problem I have ever seen is when an extended short circuit has overheated the slider springs or the pickup "brushes" on the axles. This can overheat them and they will lose their temper. Overall a superior and redundant pickup system.

The wiring can vary, and if you will remember only one piece of advice: NEVER assume what voltage the lights are inside the loco, check the voltage with a meter BEFORE any alterations.

Common screws:

With all the different brands, each has screws a little different. Also, for some reason, USAT has different screws in very similar locations.
Swapping in the wrong screws can lead to stripped threads or loose parts. It will pay off to pay close attention.


I cannot tell you how many USAT diesels I have worked on that have stripped body/shell threads, or people who have overtorqued the screws and pulled them right through the shell into the post in the chassis. Once you have done that, that locations is completely unable to share in the task of securing the shell, and there's no good way to fix this. I've worked on locomotives with enough stripped/damaged mountings that you cannot pick the loco up by the shell.

  • Body mounting: 11.5mm long, 2.6mm across the threads, head diameter 4.35 mm. Flat end with self tapping notch. These are the screws that go into the chassis, and the head rests on a ledge inside... there are long posts in the shell that draw the body to the chassis. Note: the head diameter is somewhat small, and again I will warn you to NOT overtighten these screws or you will pull them right through the chassis and render them totally ineffective.
  • Battery box: 7.8 mm long, 2.4 mm across the threads. Flat end. These are normally on the Geeps, etc, and at the edges of the chassis. Again, it is important you use the same screws. Longer screws will bottom in the holes, and wider screws will enlarge the holes too much.
  • Weights & truck pivots: These screws are 9.75 mm long, 2.95 mm thick over the threads. Note the washers used under them. Also note that often a 3 terminal regulator is attached to have the weight dissipate the heat.
  • Smoke units mounting: 7 mm long x 3 mm over the threads. Washer head with a flat end, not a pointed one. These are the ones that hold smoke units in place in the top of the shell. They can also be used to hold speakers in place in the roof of a loco. Get the wrong screws here and they will pierce the body shell on the roof, very unsightly!
  • F3A front pilot: 7.85mm long, 2.6mm over the threads. Pointed end. There are 4 of these holding the F3A front pilot on.

 

 

Converting to Kadee Couplers:

Kadee makes conversion kits, but all of them have a large offset couple and they mount to a swinging arm on a small pedestal. Due to the single screw that allows the coupler box to swivel and the offset coupler, under stress the couplers bend down, and the coupling levers drop below the rail head. This is the #1 issue with Kadees, and then people wind up cutting off the magnetic uncoupling lever or bend it way up. Either way negates the great feature of remote uncoupling. This flex also helps enhance the issue of coupler override, which leads to uncoupled trains.

I strongly recommend finding a way to make a more solid mount for the coupler and using a center-set coupler that will not "torque" down or up under stress. Below is a good way to proceed. I use these coupler boxes myself.

 CamPacBoxOfferingsRev1

 

https://camarillopacific.com/Camarillo_Pacific_Railroad/CamPac_Box/CamPac_Box.html

 

Common USAT part numbers (note I have listed wheels in increasing size):

Wheels & trucks:

Please note: the dimensions given on wheels are from the manufacturer, and not all are exact.

R2040 - wheel and axle set - solid - freight cars ( 2 axles)  

R22-011 - wheel & axle set - solid - NW-2/S4 (2 axles)

R22-135 - wheel & axle set - solid - F3/GP7/GP9/GP30/GP38-2 (2 axles) (1.126" tread diameter)
R22-136 - wheel & axle set - w/traction tires - GP7/GP9/GP30/GP38-2/F3 (2 axles)

R22-170 - wheel & axle set - solid - 44 Tonner (2 axles)
R22-171 - wheel & axle set - w/traction tires - 44 Tonner (2 axles)

R22-419 - wheel & axle set - solid - end axles - SD40-2 (2 axles) (1.265" tread diameter)
R22-420 - wheel & axle set - solid - center axles - SD40-2 (2 axles)
R22-421 - wheel & axle set - w/traction tires - inner axles - SD40-2 (2 axles)

R22-518 - wheel & axle set - solid - center axles - PA-1 (2 axles) (1.377" tread diameter)
R22-519 - wheel & axle set - w/traction tires - inner axles - PA-1 (2 axles)
R22-520 - wheel & axle set - solid - end axles - PA-1 (2 axles)

R22-622 - wheel & axle set - solid - end axles - SD70 (2 axles) (1.461" tread diameter) (1.695" over flanges)
R22-623 - wheel & axle set - solid - center axles - SD70 (2 axles)
R22-624 - wheel & axle set - w/traction tires - inner axles - SD70 (2 axles) (note that later production does not have traction tires)

Trim:

R22-301 - F3 horn, set of 2R22-304 2 ea (F3 windshield wipers, set of 2)
R22-534 - PA air horn (pk of 2)
R2060 Brake wheels. 10 in a pack, Cost $3.95
R17PN - intermodel container pins (8 each) $4.95
R22-315 - F3 ladders (hang down below body and fall off all the time)
R22-333 - F3 air hoses (one unit of 4 hoses)

Coupler parts:

R22-317 - coupler centering spring
R22-332 - coupler mounting block and pivot

Electrical:

R22-127 - screw in bulbs, number boards in diesels, low voltage - $3.50
R22-110 - gow bulbs for headlights in diesels, low voltage - $3.50
R22-17- sliders with springs

An Unofficial USA Trains Locomotive Catalog

Shawn Conahey, a.k.a EMD Trainman, has started a Yahoo group that has the best information on USAT loco and rolling stock part numbers. See the files section:

http://www.usatgscalegroup.com/phpbb/index.php

 

When USA Trains first came out as Charles Ro trains originally in the 80's, there was just one series of trains. After the name changed to USA Trains, there was more product expanding to what it is today. There is now 3 different series of USA Trains and I will explain all 3 here and what the difference is.

#1 The USA American series: This is a 1:24 scale ratio series product line up which was the original product line up made by Charles Ro back in the 80's. This series is not exatly the most realistic one USA Trains makes, but you don't have to worry about buying 20ft diameter curves to run any of this series on. On this series the detail parts such as grab irons and steps come in a kit bag and you install them. This series also comes with plastic wheels to further reduce costs

Here is a list of American Series rolling stock that was made.

1) Woodside Box car
2) Woodside Reefer Car
3) Simulated Steel Box car not to confused with the Ultimate series 40ft box car
4) Two Tier Auto Carrier
5) All Work Series Rolling Stock
6) Ore Car
7) Piggy Back Flat Car
8) Pipe Load Flat Car
9) Woodside Caboose
10) Center Beam Flat Car

The center beam flat car and piggy back flat car are no where near the correct size for the scale ratio, but USA rain captures enough in the model for people to buy and you don't need 20ft diameter curves to run a full size center beam flat car in G scale.
There is no American Series locomotives at this time.

#2 The Ultimate Series: "As Real AS It Gets" was USA Trains motto whe they introduced this new exciting series of more modern type rolling stock which is all 1:29 scale ratio. This is the most realistic series of rolling stock that USA Trains offers. I'm not saying they have the correct amount of rivets or brakes or exact measurements for their scale, so please no 100 responses about this is not correct or thatt is not correct for this road name. I'm just saying the Ultimate Series is USA Trains most realistic line up, as well as very detailed line up. There are alot of fragile detail parts on this series also. Here is a list of Ultimate Series rolling stock that USA Traiins makes. This series of rolling stock already has the detail parts already installed. This series also comes standarrd with a nice upgrade set of metal wheels.

1) Extruded Aluminum Passenger Car
2) Center Cupola Caboose
3) Bay Window Caboose
4) Extended Vision Caboose
5) 55ft 4 Bay ACF Hopper Car
6) 55ft Modern Tank Car
7) Depressed Center Flat Car
8) Intermodal Container Car
9) 40ft Box Car
10) 50FT Box Car
11) 40FT Reefer Car
12) 50FT Mechanical Reefer Car
13) 70 Ton 3 Bay Hopper Car
14) 10,000 Gallon Tank Carr
15) Woodchip Hopper Car
16) Intermodal 5 Unit Articulated set

Locomotives

1) Dockside 0-6-0T Switcher
2) SD70-MAC
3) PA1 / PB1
4) SD40-2
5) GP-30
6) GP38-2
7) GP-7 / GP-9
8) F3A / F3B
9) S-4 Switcher
10) NW-2 Switcher
11) 44 Tonner Switcher
12) Speeder

#3) The Prestiage Series: This is USA Trains newest series and is also a 1:29 scale ratio. What makes this series different is that it's made mainly from diecast metal and has alot of metal detail parts making this series the Cadillac of USA Trains. This wonderful series only has locomotives in it and includes sound.

Here is a list of Prestige Series Locomotives

1) GG1 Locomotive
2) J1E Hudson
3) Big Boy Steam Locomotive

Special Note: Be sure to ask the bidder o ebay to distinguish which USA Trains box car they have. I have seen many people on ebay get the America Series simulated steel box car confused with the Ultimate Sries 40ft box carr. Remember all American Series rolling stock you have to attach all detail parts such as grab irons and steps and the Ultimate series already has it installed.
 

 

Sub-Pages

Click the links below to go "deeper" into details on USA Trains motive power

  Split Axle Problems     Diesel Motor Block Tips    DCC Installation Techniques     0-6-0 Docksider  
  4-6-4 Hudson    4-8-8-4 Big Boy    44 Tonner    F3 
  GP7    GG-1    GP38-2    NW-2  
  PA    S4    SD40-2    SD70 
Weather Underground PWS KCACARLS78